W@rI3R35107

123 POSTS 0 COMMENTS


    This Video shows the build of a simple distillation unit from a water bottle that can be used to make fresh water from ocean water. Any steel container could work for this project. I almost used a small stainless steel food container, but decided a water bottle was a more practical object to carry.Knowing how to make distilled water is not just useful in a survival situation. It can also be an invaluable skill if your home’s tap water contains certain chemicals or impurities that you’d rather not drink.

    Watch the DIY Simple Salt Water Distiller Build



      This Video shows the build of a Solar Evacuated Thermal Vacuum Water Pump works by harnessing the energy of the sun in the day time and then uses the cold of night to create a vacuum in the system that is used to pump water. This is a working prototype of an idea on how to pump water from stagnant water sources cheaply using no moving part.By using the sun’s energy to generate both a pressure and a vacuum cycle we create a very efficient water pump, that has only two simple moving parts. This pump was able to move one gallon every cycle to 8 feet high, by creating artificial day/night cycles the pump could move about 1 gallon every 30 minutes of sunlight, or about 12 to 20 gallons a day.

      Watch the DIY Homemade Thermal Vacuum Water Pump Build Video


        This video shows the build of a Simple Pex Coil Solar Thermal Water Heater.asy DIY! No Soldering, Clamps, Crimp Rings, Glues, Unions, or that expensive crimping tool! in my design it’s just 2 push-to-fit “shark-bite” connectors! (located outside of collector) and because it’s all one piece of tube, the unit has no potential internal leak points.PEX is sturdy, tough and rigid. water temp rating range… 33F to 185F-200F (93°C) water! …and if temps hit or fall below 32F (0°C) it’s freeze damage resistant! it’ll freeze but doesn’t break. the connectors are made to last at least 25 years and pipe is rated 50+ years.

        Watch the DIY Homemade Solar Thermal PEX COIL Water Heater Build Video


          This Video shows the build of a Homemade 12VDC Mini Box Fan! w/motor speed control!Powered with a 12v battery or 12v solar panel! Made Sturdy and is SUPER POWERFUL! pushes more air than a fan twice its size.Ithas a whopping 1500 CFM air-flow volume with wind speeds measuring in at over 20 MPH! (32 kph) and with the motor control switch you can set it to run at any of 100 different speeds! .Great for off-grid use, camping, emergencies or everyday use. tip: run it from a cars’ 12v cigarette lighter plug.

          Watch the DIY Homemade 12VDC Mini Box Fan Build Video


            This video shows the build of a simple Homemade Water-Chilled” Radiant Air Cooler! w/motor speed control!.Made with an 8×8 “water-to-air” heat exchanger, small water pump and a 7″ fan. This new design cools air by pumping ice-water (or cold water) thru a water-to-air heat exchanger (copper/aluminum radiator) and then drawing the warm air thru the unit using a 12v radiator fan. the air that is produced is cooled dramatically with no increase in humidity and no need to vent any part of the unit to the outside. the heat is essentially captured into the cold water and the “cold” in the water is released into the room as cold air.

            Watch the DIY Homemade Offgrid Radiant Air Cooler Build Video


              This video shows the build of a Homemade Hot Water Air Heater using an old heat exchanger and a car radiator fan.This unit provides near-instant warm air.The Air-Flow: it’s adjustable from 10 CFM to 1500 CFM. max breeze 20 Mph! The Temps: With input water temps between 120F to 150F the output air temp ranged from 85F to 110F. *or from heat pump temps up to near furnace temps! easily warms a room or two, maybe more.The heart of the unit is an 8×8 Copper/Aluminum Heat Exchanger., This unit can easily be run straight from a 12v solar panel or battery so it’s “off-grid” ready. Simply mounted the fan in front of it,then connected the pipes. then you just connect a small water pump (200-350 gph) to one of the pipes and drop both pipes into a water-filled sink,almost immediately it creates very warm air (in under a minute).

              Watch the DIY Homemade Homemade Hot Water Off grid Air Heater Build Video

              This video shows the complete build of a Portable Rocket Mass Heater. This heater goes together like an erector set and comes apart just as easily. It’s custom mini mass. This heater can save you up to 80% on your heating bills. It is super efficient. This heater is beautiful and built completely from reclaimed and repurposed items. This rocket mass heater is Artistic one of a kind! This rocket mass heater is made with air crete, and is budget friendly, handmade, and better than a wood stove.The advantage of this rocket mass heater is the huge increase in the efficiency of capturing and storing the available heat.

              Watch the DIY Homemade Efficient Portable Rocket Mass Heater Build Video

                This video shows the generation of Unlimited hot water  100% Off the Grid without electricity by converting an old propane tank to burn underwater as an immersion heater for a lot of hot water.Here,I use a homemade underwater wood stove to make a lot of hot water in a relatively short time.I also make use of the waste heat to cook breakfast.Almost 75-80 gallons of hot water in 1 hour with wood.Really a great way to heat a lot of water.

                Watch the DIY Homemade Underwater Wood Stove Water Heater build


                  This video shows the build of a redneck style off grid wood burning heat exchange we use to heat our house in the winter. It will keep your home warm without electricity, or using the furnace. The air comes in through the front, where there is a lot of spaces along the bottom of the barrel, then gets heated and rises through the duct in to the house.Here,the air from the house does not go into the exchanger, it only pushes warm air into the house.

                  Watch the off grid wood burning heat exchanger Build Video

                    This video shows the build of a $100K worth WaterJet Cutter for about $200 using a cheap pressure washer.Waterjet is the ultimate machine tool, no matter the application.This is because its a Cold Cutting Process which means no heat or stress is imparted into your cut materials.Also you can take the part directly off of the cutting table, no secondary finishing required.Also it eliminates slag deformation and dross waste – unfortunate effects found in plasma and laser cutting processes.

                    Watch the DIY Homemade Cheap  WaterJet Cutter Build Video

                    This video series shows how you can generate 24/7 Free Electricity From Across the Pond with a converted ceiling fan Permanent Magnet Alternator, a...
                    Share