How to build an awesome Drill Powered Winch .Lift a Car or other Heavy loads effortlessly using a simple Cordless Drill

This video shows how a simple Cordless Drill can effortlessly lift or move heavy loads. Definitely beats a Come Along.The winch in the video was purchased from Harbor Freight.With a snatch block this will lift 4000lbs which will pull a 20,000lb vehicle up a 10% grade.A snatch block is a really neat thing. By taking the cable out of the winch and through the pulley of the snatch block, then back to the winch it doubles the pull capacity.

It also halves the speed of the item being pulled/lifted but it is a worthwhile trade off. You can keep adding pulleys and running back and forth to reduce the strain on the winch.You will see that a cordless drill lifting a car off the ground is pretty damn impressive

Watch the DIY Homemade Cordless Drill Powered Winch Build Video



RECENT POSTS YOU MIGHT LIKE
  • DIY Video:How to recycle scrap metal in the backyard by building a simple Mini Metal Foundry from start to finish
    This video shows you how to recycle scrap metal in the backyard, with a homemade, Mini Metal Foundry.Depending on where you get, or find, your materials the cost can range anywhere from $5-$25 per unit. With the materials I used, I was able to make 2 units for under $40 ($20 each).Even on the high end, this is probably one of the cheapest, reliable, backyard foundries that can be made.I used mine to melt soda cans, and extract the aluminum for future metal casting projects. All the soda cans came from a local recycling depot.
    Watch the Homemade Mini Metal Foundry  Build
  • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
    This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
    Watch the homemade Micro hydro Turbine Build and setup

  • DIY Video:How to build a Super Efficient Rocket Mass Heater from reclaimed and repurposed items and save up to 80% on your heating bills
    This video series shows the build of a one of kind Rocket Mass heater.This heater uses  aerate concrete and keep the 'mass' of the rocket mass heater light. This heater goes together like an erector set, and comes apart just as easily. It's custom exhaust can be rotated 180 degrees in any direction, and can be routed through a mass bench as well as its custom mini mass. This heater can save you up to 80% on your heating bills.This heater is beautiful and built completely from reclaimed and repurposed items. The advantage of this type of rocket mass heater is the huge increase in the efficiency of capturing and storing the available heat.

    Watch the DIY Homemade Rocket Mass heater Build Videos from start to finish