How to build an Inexpensive Backyard Concrete Mixer at Home using an Old 55 gal Barrel



RECENT POSTS YOU MIGHT LIKE
  • DIY Video : How to build a Homemade Chainsaw Mill from Scratch. Step by step Build Instructions
    Chainsaw mills are a great cost effective way to turn large branches or logs into, slabs, boards or posts. They are very portable and don’t require the serious space or investment of a fully dedicated mill, once you are done milling, simply detach your chainsaw and use it for any of your other tasks. This Video shows the build of a Homemade Chainsaw Mill from Scratch.This is a great tool for builders, outdoors men, and woodworkers. It offers them an inexpensive way of converting their chainsaw into lumber making machines.

    Watch the DIY Homemade Alaskan Chainsaw Mill Build Videos

  • How to build an Inexpensive Backyard Concrete Mixer at Home using an Old 55 gal Barrel
    This video shows the build of a Homemade Inexpensive Concrete Mixer made out of 55 Gal Drum from start to finish.This build uses a salvaged 90V DC Gear driven motor.A motorcycle sprocket is welded on to the front of gear drive which fits the chain that goes around the Barrel. The most important benefit of a concrete mixer is that it can save a lot of labor. Mixing cement by hand is a difficult and time-consuming process.Another benefit of using a concrete mixer is that the mixer can ensure that cement or concrete is blended homogeneously, creating a much better result than mixing manually and helping prevent flaws in the finished cement.

    Watch the DIY Homemade Simple 55 Gal Drum Concrete mixer Build

  • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
    This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
    Watch the homemade Micro hydro Turbine Build and setup