How to build an Inexpensive Geothermal Air Conditioning System to Cool your Home using an Old Car Radiator ,Solar Panel.



RECENT POSTS YOU MIGHT LIKE
  • How to build a Homemade Clothes Washer that require no electricity.Also works as a Composter
    This video shows the build of a simple off grid washer machine which can also act as a composter.If you thought the only way to wash clothing off grid was to take them down to the creek and beat them against a rock, think again.All you need in order to build this washer is a plastic barrel, some pipes, and – you guessed it – a wooden frame. The frame is meant to support the barrel and keep it from rolling away. You’re going to use the pipes to attach the barrel to the frame, as well as to create the lever that helps you wash the clothes.

    Watch the DIY Offgrid Clothes Washer /Composter Build Video

  • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
    This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
    Watch the homemade Micro hydro Turbine Build and setup

  • DIY Video : How to build a Homemade Atmospheric Water Generator . Produces/Extracts Distilled Water from the air
    This video shows the build of a Homemade DIY Atmospheric Water Generator!.ThisUnit pulls Pure 'distilled water' straight out of the air. This simple design pumps near freezing water thru a long section of copper coil. Coil becomes very cold and dew (condensate) forms on the coil. The dew is then caught by a drip-pan located beneath the coil.This unit has the added benefit of dehumidifying the air.I used only aluminum and copper in this version. main thing with these is to keep the coils clean. if coils are cleaned after each use, the water generated is 'distilled water.

    Watch the DIY Homemade Atmospheric Water Generator Build Video here