How to build a Homemade Wooden Bandsaw Mill from Scratch.Step by step build Instructions








RECENT POSTS YOU MIGHT LIKE
  • How to build a Homemade Large Water Wheel Electricity Generator from Sap Buckets,Old Bicycle Parts,Treadmill motor that can charge Batteries,Run Lights
    This Video series shows the build of a Large Homemade Water Wheel Electricity Generation System using few Maple Sap buckets,Old Bicycle Parts,thread mill motor and other easily available materials.Made of All leftover scrap metal parts and some sealed bearings from 2 old motors, also pipes, bed frames and a 2 foot section of water well pipe suspended on said roller bearings..Part 2 of the series explains the the sleuce trough suspension and connecting the alternator and the last part shows how all the parts are connected and then charges a car battery very well.

    Watch the DIY Homemade Large Sap Bucket Water Wheel Generator Series

  • DIY Video : How to dig your own Water Well from start to finish and save a lot of money
    This video series shows how to dig yourselves a water well by hand from start to finish and thereby save more than 2000 to 3000 Dollars .I am using a 6" auger post hole digger available at most hardware stores. One of the hurdles to living off grid is having a clean water supply. One of the very best ways to address that issue is with your own well..Learning how to dig a well is a good lesson that every prepper should master.Even if it doesn’t come to a survival scenario, having your own water supply means that you’re basically off the grid. You’re not dependent upon third parties.

    Watch the DIY Hand Dug Water Well Video Series

  • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
    This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
    Watch the homemade Micro hydro Turbine Build and setup