How to generate 24/7 Free Electricity from across a Pond/Creek by building a Ceiling Fan Alternator Hydro System



This video series shows how you can generate 24/7 Free Electricity From Across the Pond with a converted ceiling fan Permanent Magnet Alternator, a water wheel made with bicycle rims and PVC pipe end-caps and just 4 feet of “head”.This can produce practical power that can be used directly for lighting or to charge batteries which can later provide 120 AC power through an inverter to power literally anything in your home.

Watch the DIY Homemade Ceiling Fan Micro Hydro Power Generator Build Series



RECENT POSTS YOU MIGHT LIKE
  • DIY Video : How to build an Ammo Can Double Burner Rocket Stove from scratch . Step by step Build Video Instructions
    This video shows the step by step build of a Double Burner Rocket Stove made from an Old Ammo Can.The can is around 19″ x 10″ x 10″, I use vermiculite as insulation, some use sand instead but I like vermic as it is fairly light.If you remove some of the insulation and it’ll be a mini barrel stove for heating too.Here i use a Black and Decker Scorpion saw to cut the pipes and just a cheap bi-metal hole saw to do the holes. I’ve cooked a full steak dinner in the woods on it and it worked great.

    Watch the Homemade Ammo Can Double Burner Rocket Stove build

  • How to run a Homemade Generator on Wood or even Trash/Garbage
    This video series shows how you can run a generator on wood or even trash.When wood is heated it releases a few different types of gases, I use a homemade gasifier to extract these gases out of the wood, I first run the gas through a condenser coil to condense any steam and tar out of the gas, I then use a bubble filter to catch that water and tar and it also helps in filtering out some of the unwanted smoke, next the gas runs through a homemade filter to remove the last of the unwanted byproducts, The wood gas then runs directly into the air intake on the 25cc engine.

    Watch the DIY Homemade Wood Gasifier Build Video

  • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
    This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
    Watch the homemade Micro hydro Turbine Build and setup