DIY Video : How to build a Homemade Atmospheric Water Generator . Produces/Extracts Distilled Water from the air



    RECENT POSTS YOU MIGHT LIKE
    • DIY Video:How to build an Emergency Water Distillation Still for Survival Bug-Out Bag
      This video shows the build of a Emergency Water Distillation Portable Still that removes biological, salt and heavy metal contamination from drinking water.The still is made by putting an upside-down stainless steel funnel over a pot of boiling water as a lid. Ideally the pot is designed for cooking, but in an emergency any metal container, such as a soda can, may be used. Connect a 1/2 inch diameter copper pipe to the funnel with three 45 degree elbow fittings. Put a damp rag on the pipe to condense the steam. Fresh, drinkable water will drip out of end of the pipe

      Watch the DIY Homemade Emergency Water Distillation Still Build

    • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
      This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
      Watch the homemade Micro hydro Turbine Build and setup

    • DIY Video:How to build a Homemade DIY Rocket Stove Boiler to heat your Home.Fully offgrid, cheap and really efficient

      This video shows the step by step complete build of a Hydronic Home heating system by using a DIY Rocket Stove Water Heater.This stove is smokeless and is hooked up to hydronic floors and making hot water 120-127°f output (approx 40°f temp boost @ 4gal/min).The boiler transfers the heat through water tubes in the heat exchanger. The heated water on the other side of the heat exchanger is then delivered to base boards, radiators or in-floor heating tubes throughout your home.The main benefits of this system is that Heat is evenly distributed in a room: no drafts or hot and cold spots as with forced air and hot water from the boiler can also be directed to an indirect water heater to supply your home with hot water

      Watch the DIY homemade DIY Rocket Stove Boiler Build