DIY Video : How to build a Simple Homemade PVC Wind Turbine Generator with Swivel Top .Produces electricity to run lights, charge batteries



    RECENT POSTS YOU MIGHT LIKE
    • DIY Video: How to build a really efficient Portable Ammo Box Wood Stove
      This video shows the build of a really efficient Portable Ammo Box Wood Stove .Great for outdoorsmen, adventurers, preppers, survivalist and anyone looking for a small, portable stove for both heating and cooking. Plus, it's a fun project and makes a great gift for the outdoor enthusiast or hobbyist. The materials needed for this project are 50 Cal Ammo Box,Stove Rope Kit,Propane cylinder,Fiberglass Cloth,Mica Sheet,12" Steel Tent Stakes, 4mm thick steel plate,22 gauge steel sheet,16 gauge, Steel rivets ,BBQ skewer,4 copper pennies,2 small compression springs,3 ½” hose clamp.  

      Watch the Portable Ammo Box Wood Stove Build Series

      Other Articles:
    • How to make a Survival Rope Making Machine at home from easily available materials
      This project goes over the build of a Homemade rope making machine using a simple cordless power drill and some inexpensive materials that are sourced from the local hardware store. Here are the materials needed for this project: Three quarter inch by five inch eye bolts with hex nuts Fender Washers Cut Washers Hex Nuts Plastic Castor Wheels two by two and one by six by six piece of lumber Old bicycle tire tubes Take the board and cut it to length of seven and a half inches and took the first piece and doubled it over the second one and cut them together so that they are exactly the same length. Then I took a piece of two by two and cut it eight and a half inches long. Take large fender washers and position them on the board forming a triangle, you want to do it in such a way so when you add your two by two to the top as well as the bottom, it has similar spacing at the top and the bottom. Put the two boards together, mark the centers and drill the holes. Next step is to build the metal spinning hooks. These spinning hooks are going to be made out of eyebolts which is used as a hook to put the strings on. We take 3 plastic castor wheels and use them as a pulley , connect them together with a small piece of bicycle tire tube so that when one is spun ,all three of them would spin together. We take the 3 eyebolts and push it through the hole and secure them tight with a small cut washer and hex nut. It is locked in place but should spin freely. Put with wheels through the bolts and secure them using fender washers, cut washers and nuts. Take an old used tire tube piece and line it up between the two washers and cut up a piece that is roughly about the same distance as that gap. We loop the tube over the pulley all at once.The Second board is pushed through the bolts over the wheel pulleys.Make sure everything is lined up symmetrically. When we turn one bolt, the belt drives the other two pulleys and they all spin together. As we are running the hook spinner, we are going to need something to hold it at the other end, To make the other end of the mechanism that holds the strings in place, we take six inch piece of common board and eight and a half inches of our two by twos on the bottom to secure it as a base and them we clamp it over a table. The idea is that as each hook begins to spin, the two cords attached to it will intertwine with each other. And then eventually all three of those cords will mesh together to make a nice three stranded rope. As the strands are twisted, it creates tension on the backboard. To relieve the tension, we drill a hole through the backboard and tie the rope to another counterweight rope through a swivel hook that pulls the tension and allows it to rise as the cord is pulled. We also make a rope makers top that will help guide those strands into the beautiful three strand cord. We add two ropes between the spinner mechanism as guidelines and connect it to the back board to accommodate the rope makers top. The idea is that as the tension builds it will glide forward and guide the individual strands into place to form a three stranded rope. We sandpaper the holes on the rope makers top to make it smoother so that the lines won't snag up when they start twisting. We put a wooden knob on the back to reduce the friction so that the rope makers top can slide smoothly. Loop the cords through each of the three hooks on our rope maker machine .Form a slipknot and connect it to the swivel hook. We have our rope machine build complete . To tie and cut of the rope, take a small piece of electrical tape and wrap it around the end where you want to cut it off. Cut The Rope at the back just where the electrical tape ends . https://www.youtube.com/watch?v=ddenqErLL0Q https://www.youtube.com/watch?v=uEvM6ue3L7E https://www.youtube.com/watch?v=RM9GY-n6PEA
    • DIY Video:How to build a simple Off Grid Electricity Generation System using Two Batteries
      This project shows you how to generate Off grid AC Power using a simple Solar power station with 2 batteries.This system can provide enough off the grid power to run your appliances around the house.You can easily run light,a laptop computer, small tv and fan for several hours. Most of the item required can be bought from your local store or Amazon.The rough cost of building this system is as follows : $150 for 100W Solar Panel $75 each for 2 batteries. $20 for 400w Inverter $40 for charge controller. The whole system comprises of four things, a couple of batteries, inverter, and a charge controller.The inverter is purchased from Harbor freight ,the charge controller from fry electronics.The deep cycle batteries are from Walmart. So you start by setting up your panels outside. In this case, I have six one amp panel set up, 15 watts a panel, so that's 90 watts coming in. I lead them straight down to the main connection, it's just the six black wires all connected together and twisted tightly to that extension cord wire and the six red ones connected.Feed the line into your house,goes straight to the charge controller. The output wire from the charge controller goes into the battery.So solar panels to charge controller ,charge controller to lead battery in your bank.And as you want to expand this to two,three or more batteries, just use some automotive cables and go from positive terminal of one the positive of the other. And with a black wire, negative terminal to negative terminal, the other one. When you want to run something, just get your inverter that converts the power from DC to AC, take the clamps, clamp them onto that same lead battery in the system. So again, red to the positive side, black to the negative side and flip it on. So remember, when you hook things up like an inverter, or the charge controller or voltmeter, anything you're going to hook up on here, make sure you always pick one of the batteries to be the lead battery and hook everything to that. Whether you parallel one extra battery with it, or five or six or however many you want to put on there. Also added here is a lighted voltmeter which gives you a constant reading on your battery bank so you know exactly what's going on with it at all time. https://www.youtube.com/watch?v=cgEvCLJuBkg https://www.youtube.com/watch?v=8LAjx_XAR90 A simple system that can come really handy during a power outage or in any emergency situation.