DIY Video : How to build a DIY Pex Coil Solar Thermal Water Heater. Simple and Efficient!!



    RECENT POSTS YOU MIGHT LIKE
    • How to make a Survival Rope Making Machine at home from easily available materials
      This project goes over the build of a Homemade rope making machine using a simple cordless power drill and some inexpensive materials that are sourced from the local hardware store. Here are the materials needed for this project: Three quarter inch by five inch eye bolts with hex nuts Fender Washers Cut Washers Hex Nuts Plastic Castor Wheels two by two and one by six by six piece of lumber Old bicycle tire tubes Take the board and cut it to length of seven and a half inches and took the first piece and doubled it over the second one and cut them together so that they are exactly the same length. Then I took a piece of two by two and cut it eight and a half inches long. Take large fender washers and position them on the board forming a triangle, you want to do it in such a way so when you add your two by two to the top as well as the bottom, it has similar spacing at the top and the bottom. Put the two boards together, mark the centers and drill the holes. Next step is to build the metal spinning hooks. These spinning hooks are going to be made out of eyebolts which is used as a hook to put the strings on. We take 3 plastic castor wheels and use them as a pulley , connect them together with a small piece of bicycle tire tube so that when one is spun ,all three of them would spin together. We take the 3 eyebolts and push it through the hole and secure them tight with a small cut washer and hex nut. It is locked in place but should spin freely. Put with wheels through the bolts and secure them using fender washers, cut washers and nuts. Take an old used tire tube piece and line it up between the two washers and cut up a piece that is roughly about the same distance as that gap. We loop the tube over the pulley all at once.The Second board is pushed through the bolts over the wheel pulleys.Make sure everything is lined up symmetrically. When we turn one bolt, the belt drives the other two pulleys and they all spin together. As we are running the hook spinner, we are going to need something to hold it at the other end, To make the other end of the mechanism that holds the strings in place, we take six inch piece of common board and eight and a half inches of our two by twos on the bottom to secure it as a base and them we clamp it over a table. The idea is that as each hook begins to spin, the two cords attached to it will intertwine with each other. And then eventually all three of those cords will mesh together to make a nice three stranded rope. As the strands are twisted, it creates tension on the backboard. To relieve the tension, we drill a hole through the backboard and tie the rope to another counterweight rope through a swivel hook that pulls the tension and allows it to rise as the cord is pulled. We also make a rope makers top that will help guide those strands into the beautiful three strand cord. We add two ropes between the spinner mechanism as guidelines and connect it to the back board to accommodate the rope makers top. The idea is that as the tension builds it will glide forward and guide the individual strands into place to form a three stranded rope. We sandpaper the holes on the rope makers top to make it smoother so that the lines won't snag up when they start twisting. We put a wooden knob on the back to reduce the friction so that the rope makers top can slide smoothly. Loop the cords through each of the three hooks on our rope maker machine .Form a slipknot and connect it to the swivel hook. We have our rope machine build complete . To tie and cut of the rope, take a small piece of electrical tape and wrap it around the end where you want to cut it off. Cut The Rope at the back just where the electrical tape ends . https://www.youtube.com/watch?v=ddenqErLL0Q https://www.youtube.com/watch?v=uEvM6ue3L7E https://www.youtube.com/watch?v=RM9GY-n6PEA
    • How to build a Homemade Multi Use Water Purifier that uses no electricity .Works as Water heater and stove burner too….
      This project goes into the build of a simple and cheap two stage DIY water filter.Also doubles as a stove burner. The materials needed for this build are some bricks,bottles,copper coil,activated carbon,sand,gravel I got the sand and activated carbon water filtration part on the far left. In the middle, I've got it heated in a copper coil running on isopropyl alchohol. The purified water is coming out on the right side. The first step is to make the 1st stage filter. We take a 2L bottle cut in half, drilled a quarter inch hole on the bottom and drop in a couple of cotton balls and pack it in there. Next step is to add the activated carbon,sand and gravel.Rinse all of them before adding . Align the bricks and place the cans on top. Place a small tin with the isopropyl alcohol inside the middle can. A copper coil is inserted into the middle can and connect between the first can and the water bottle. Add the sand mixture filter bottle on top of the first can below the copper pipe. For the first can the one that holds the activated carbon filter,just remove the label and drill one small hole at the bottom. Then for the second cam that holds the copper coil, you cut down the top, take about a third of circumference off and cut about two thirds of the way down. Then put one small notch on the top and a hole down below for the coil. To make the copper coil just wrap it around from top to bottom in a smallcan, push the can out and leave about a foot on either side. Notice I added a couple of bricks and pointed the end of the copper tubing down directly into the can so we won't lose hardly any water and make sure to drill those steam vents so the pressure doesn't build up. Make sure to drill vents on the bottle so that the pressure doesn't get build up. Pour the alcohol under the coil and fire it up. Just put a little in ,you don't need too much. A full glass of water gets purified in three to three and a half minutes. This gravity fed two stage water filter should take care of pond water stream water swamp water, just about any water you can think of. Don't try using this without the heavy sand gravel and activated carbon in there or the water will backflow and it may spray out. An easy way to store this filter when you're not using it is just save the bottom half of the two liter bottle you cut in half and drop the filter in it ,holds it perfectly. This cheap 2 stage heated oil water purifier can also be used to both purify water and cook at the same time.
    • DIY Video : How to build an Off Grid Water Heater – Hot Water with DIY Firestove
      NEED HOT water? Camping, off grid, this Off Grid Water Heater is the unit to have!.It has given my off grid home comfort and HOT water! VERY simple setup and very economical.Water heating is essential not only for comfort off the grid, but for survival.Hot water is definitely a luxury that you miss when you actually have to go without.In most homes your hot water heater is consuming energy day and night, 24-7. Most hot water heaters are set to keep the water hot at all times, even while you are in bed. This can be quite wasteful. And with the rising energy costs, many people are looking for alternatives,this Off Grid Water Heater can be really helpful.

      Watch the DIY Outdoor Off Grid Water Heater build video