How to build a Simple,Effective Metal Melting Furnace using Old Steel Container and Ceiling Fan parts. No welding required




RECENT POSTS YOU MIGHT LIKE
  • How to convert an Old Ceiling Fan Motor into a 70W Efficient Single Phase Alternator Generator
    This project goes over the conversion of an old ceiling fan motor into an single phase alternator .You can't take your standard AC electric motor and spin it and get an electrical current out of it unless you modify it. The ceiling fan motor used here will produce about 70 volts at one amp which is roughly 70 watts. Through a bridge rectifier we can get about 70 watts of power out of it. We start by pulling the cover of the fan. Inside we have a squirrel cage rotor in the middle and 6 coil windings around it. The coil windings are placed in clockwise and anti-clock wise directions inside the stator. Next we remove the circular rotor from the threaded shaft which is attached to it with help of a vice. We attach the shaft with the rotor through it within a vice. With the help of an extra piece of pipe to give leverage, we press them against the rotor and push it away from the rod and pop it off. We are replacing the rotor that we have detached from the shaft with a two inch hex steel bar . It has six sides that matches with the six coils from the stator. With the help of one eighth inch drill bit we cut a hole in the center of our hex bar. We put the hex bar through the shaft and fit them snugly around the threaded area. We take six one half inch neodymium or rare earth magnets and place them along the the 6 sides of the hex bar. We place them in such a manner that the poles of the magnets are opposing each other. For permanent usage, wrap this with a little bit of tape or glue so that they are held in place securely. We place our modified rotor in the middle of the stator and align them such that they fit in tightly. The outer screen is bolted back onto the motor. We can also add second set of magnets to increase the magnetic field of the rotor .This will also bring it closer to the coils on the outside and increase the overall voltage. To convert the alternating current generated by our ceiling fan alternator to direct current, we use a bridge rectifier. It has 4 poles, 2 for connecting our alternating current, the other plus and negative for DC power. https://www.youtube.com/watch?v=k-4IbLOZwnA
  • How to build a Homemade Multi Use Water Purifier that uses no electricity .Works as Water heater and stove burner too….
    This project goes into the build of a simple and cheap two stage DIY water filter.Also doubles as a stove burner. The materials needed for this build are some bricks,bottles,copper coil,activated carbon,sand,gravel I got the sand and activated carbon water filtration part on the far left. In the middle, I've got it heated in a copper coil running on isopropyl alchohol. The purified water is coming out on the right side. The first step is to make the 1st stage filter. We take a 2L bottle cut in half, drilled a quarter inch hole on the bottom and drop in a couple of cotton balls and pack it in there. Next step is to add the activated carbon,sand and gravel.Rinse all of them before adding . Align the bricks and place the cans on top. Place a small tin with the isopropyl alcohol inside the middle can. A copper coil is inserted into the middle can and connect between the first can and the water bottle. Add the sand mixture filter bottle on top of the first can below the copper pipe. For the first can the one that holds the activated carbon filter,just remove the label and drill one small hole at the bottom. Then for the second cam that holds the copper coil, you cut down the top, take about a third of circumference off and cut about two thirds of the way down. Then put one small notch on the top and a hole down below for the coil. To make the copper coil just wrap it around from top to bottom in a smallcan, push the can out and leave about a foot on either side. Notice I added a couple of bricks and pointed the end of the copper tubing down directly into the can so we won't lose hardly any water and make sure to drill those steam vents so the pressure doesn't build up. Make sure to drill vents on the bottle so that the pressure doesn't get build up. Pour the alcohol under the coil and fire it up. Just put a little in ,you don't need too much. A full glass of water gets purified in three to three and a half minutes. This gravity fed two stage water filter should take care of pond water stream water swamp water, just about any water you can think of. Don't try using this without the heavy sand gravel and activated carbon in there or the water will backflow and it may spray out. An easy way to store this filter when you're not using it is just save the bottom half of the two liter bottle you cut in half and drop the filter in it ,holds it perfectly. This cheap 2 stage heated oil water purifier can also be used to both purify water and cook at the same time.
  • DIY Video : How to build a Survival Water Distillation System for under $5 and turn Salt Water Into Fresh Water
    This video shows the build of a Survival Water Distillation unit using simple and easy to find items. If you were to actually purchase all the items needed this project would only cost $2-5.This Water distillation can treat contaminated water, purifying it completely, making it safe to drink.This is very ideal in a Survival situation or when SHTF.These distillers are effective, safe, and cheap, as they can be made from materials that are easy to obtain.  They are able to purify contaminated water and salt water.

    Watch the DIY homemade simple Survival Water Distillation Still Build