DIY Video : How to build a Thermal siphoning rocket stove for an off grid water system. Clean and efficient burn

     



    RECENT POSTS YOU MIGHT LIKE
    • DIY Video:How to build a Homemade Double Barrel Garage Heater out of Old Water Tanks .Efficient,clean burn and cheap!
      This project goes over the build of Double Barrel Stove out of two old scrap water heaters for the shop. The first step is to disassemble both the old electric hot water heaters to get their tanks out. Take a grinder and cut a section off from the top of the water heater tank. This tank will become the bottom tank. Remove any calcium and mineral that ends up developing deposits inside the bottom of the tank. Take a 12 gauge plate steel and put our top drum upside down and scribe a circle out of them from the end and cut it. Weld the steel piece onto the drum. You need to do the same for the other drum too because with these double barrels, you are basically making two stoves, just connecting them in the middle. Now both the top tank and bottom tank ends have been polished and cleaned .Remove any insulations, paints and glues from them if they have any. Make sure all the rough pieces on the tank are welded on ground down. Cut a small piece of pipe that acts as stack between the 2 tank. Next step is to add a small support bracket on the top of the bottom tank that will help support the top tank. Cut a hole on the bottom tank .This will be where the stack goes between two of them. Fill the drain plug down at the bottom . Take the top tank, cut and weld the top exhaust stack that will be six inch outlet for the smoke. We also add a six inch inlet that goes up to the top that forces your your smoke and the gas has to go across the length of the barrel. The bottom barrel will be connected to this. Both barrels are welded together, the bottom barrel is welded onto the mid stack which connects the top barrel with the exhaust stack. In order to support the barrels, we take the scrap pipes lying around and make legs as a support structure for the stove. Next is the door fabrication. We cut a hole for the door in the bottom barrel. A couple of hinges, door catch are welded on to this end. An air inlet pipe is threaded onto a plate. The whole unit is then attached to the door. A handle is attached to the inlet pipe so you can open and close whenever you want to control the flow of the air intake. https://www.youtube.com/watch?v=fTj4pjJ4DT0
    • How to build a Super Efficient Outdoor Wood Stove Heater from an Old Propane Bottle
      This project goes over the build of an efficient outdoor wood burning stove heater out of an old propane bottle and some scrap metal from the scrapyard. This stove has secondary burn system that helps in combustion of any unburned smoke or fume inside .Almost little to no smoke coming from the flue pipe. The first step is to make sure that the old propane tank is empty. We take the valve at the top by removing the valve protector cage. Fill the tank with water and let it sit for a few hours before we drain the tank and start cutting top and bottom. With the help of a hole saw cutter ,we cut 100mm four inch holes at the top and bottom of the tank . The top hole is for the flue pipe to sit in and the bottom hole is for cleaning the ashes out. We also remove the bottom stand too. Next, we cut a hole for the door for the stove. This is cut as high up to the top of the bottle . The door is made of chequered plate piece . We fit a rectangular pyrex dish glass piece in the middle of the chequered plate that can withstand high temperature with couple of steel bracket pieces. The glass on the door helps us to see how the secondary burn system is working inside the chamber. The door is attached to a frame through hinges. The flue outlet on the top the tank is attached through a flange piece with holes. The door handle is made of a socket wrench. The wrench is bolted to the plate and a small metal piece is welded onto to the frame to which the wrench is pulled to close the door A deflector plate made of small holes is installed inside the stove on the top . We drill 8mm holes around the top of tank and put dome bolts across them. The deflector pipe sits on these bolts. The deflector plate stop the unburned gases exiting out the flue outlet pipe. This encourages the flame that rises, pass through the deflector plate holes into the secondary burn chamber that helps in better combustion. The secondary burn system is made of stainless steel pipes .The air intake section is long enough to get the air coming in to get super heated and move into two sections filled with holes. Since not all gases from the wood combust from the primary air intake, the secondary burn pipe ensures that the air gets super heated before exiting the pre-drilled holes and helps burn the unburned gases rising from the fire before exiting the flue pipe. The secondary air intake pipe coming out of the firebox is welded on the top of the tank with a flange piece. The primary air intake pipe that goes under the door frame is made of a two inch coupler and threaded damper disc. A small metal piece is welded to the coupler with a hole in the middle. The damper disc screws in through the hole that allows us to close and open the intake .
    • DIY Video : How to Generate FREE POWER by building a Homemade Waterwheel Microhydro System from Start to Finish
      This Video Series shows step by step on How you can provide enough electricity for one house by building a Micro Hydro water wheel electric generator .Not only you will no longer dependent on the power grid, but you’ll have electricity when SHTF and more important: absolutely FREE.Unlike solar panels, a water wheel electric generator can produce electricity 24/7.Simply,the flowing, dropping water is spinning a wheel .The wheel shaft it’s connected to a simple coil generator that produces electricity. If you don’t need electricity you may adapt the water wheel to grind grain, to cut wood, strengthen iron or to sharpen tools. Anyway you choose to use it, a water wheel is an important installation when living off the grid or when SHTF.

      Watch the DIY  Waterwheel Micro hydro System Build Videos