DIY Video:How to build an awesome Roof Top Portable ABS Pipe Hot Water Heater/Shower . Great for Camping/ Outdoors



    RECENT POSTS YOU MIGHT LIKE
    • How to build a Homemade Micro Wind Turbine for under $50 that can be mounted anywhere
      This project goes in the detail on how to build a mini wind turbine..The wind turbine is a nice addition to your solar generator system for times when it’s cloudy and you are not receiving as much sunlight as you normally First step is to build some cheap PVC blades, what kind of motor we're going to be using and how we're going to attach this to the motor. We are making six blades or rotors here.What we want to do is we want to cut our PVC pipe to length first. Once you've got it cut to length, then you want to take your your straight edge again and and Marco line down the center and cut it in half. Make sure that you do that on both sides. One on this side, one on this side. And that they're perfectly in the middle so that you'll get two even sides. We need to cut a small little block down at the blade end, where we are going to put a drill hole and put a screw through it so that it attaches to the hub.On the top of the blade, we're going to cut away some of the material to resemble a swept wing, kind of at an angle. These are 14 inch long blades that is attached to the hub using set screws attached to the motor. The 12V motor used here is a 300 RPM geared motor which would be its maximum speed and it produces 600 milliamps when its fully loaded. The motor is placed inside a One and half inch PVC pipe ,another PVC Tee is connected from where the wires will down to the bottom where another 7 foot pipe that act as the tower or pole. The end of the pole goes into a shower drain which is then attached to piece of wood that acts a solid base. For the YAW system at the back end,a tail vane is made of a cheap flashing material that is bolted between an 8 inch piece of PVC.Put a hole through the middle of it with a bolt in between so that it can't move anywhere. We use an an old OSB for the base, size is about seven inches square. And then I just have a piece of treated lumber on the bottom. It's attached to this ball bearings so it can spin around. The Shower drain PVC is placed in the middle through some ball bearings. Route the wiring down through the hole for to connect to the charge controller. Next step is the wiring through the piping.We just need to connect these terminals to the appropriate sides of the motor. https://www.youtube.com/watch?v=6UZ2WtXlVoc https://www.youtube.com/watch?v=fjHW78bMUoY https://www.youtube.com/watch?v=c7a9RSzZKcE
    • DIY Video : How to Repurpose an Old Water heater into a Foundry Furnace. Easy to build,Heat up quickly and efficient
      This Video series shows how to Repurpose an Old Water heater into a Foundry Furnace.This is a great way for the do-it-yourselfer to build a foundry furnace that will last a long time, heat up quickly, be fuel efficient, easy to build, and not break the bank!.The materials needed for this build are Old Water heater,Non-firing refractory,100HT ceramic coating,Ceramic blanket.

      Watch the Old Water Heater Foundry Build Series here

    • How to build a Homemade Multi Use Water Purifier that uses no electricity .Works as Water heater and stove burner too….
      This project goes into the build of a simple and cheap two stage DIY water filter.Also doubles as a stove burner. The materials needed for this build are some bricks,bottles,copper coil,activated carbon,sand,gravel I got the sand and activated carbon water filtration part on the far left. In the middle, I've got it heated in a copper coil running on isopropyl alchohol. The purified water is coming out on the right side. The first step is to make the 1st stage filter. We take a 2L bottle cut in half, drilled a quarter inch hole on the bottom and drop in a couple of cotton balls and pack it in there. Next step is to add the activated carbon,sand and gravel.Rinse all of them before adding . Align the bricks and place the cans on top. Place a small tin with the isopropyl alcohol inside the middle can. A copper coil is inserted into the middle can and connect between the first can and the water bottle. Add the sand mixture filter bottle on top of the first can below the copper pipe. For the first can the one that holds the activated carbon filter,just remove the label and drill one small hole at the bottom. Then for the second cam that holds the copper coil, you cut down the top, take about a third of circumference off and cut about two thirds of the way down. Then put one small notch on the top and a hole down below for the coil. To make the copper coil just wrap it around from top to bottom in a smallcan, push the can out and leave about a foot on either side. Notice I added a couple of bricks and pointed the end of the copper tubing down directly into the can so we won't lose hardly any water and make sure to drill those steam vents so the pressure doesn't build up. Make sure to drill vents on the bottle so that the pressure doesn't get build up. Pour the alcohol under the coil and fire it up. Just put a little in ,you don't need too much. A full glass of water gets purified in three to three and a half minutes. This gravity fed two stage water filter should take care of pond water stream water swamp water, just about any water you can think of. Don't try using this without the heavy sand gravel and activated carbon in there or the water will backflow and it may spray out. An easy way to store this filter when you're not using it is just save the bottom half of the two liter bottle you cut in half and drop the filter in it ,holds it perfectly. This cheap 2 stage heated oil water purifier can also be used to both purify water and cook at the same time.