How to build an Emergency Deep Well Water Pump from scratch.Step by step build Instructions



Considering that most disasters can cause serious disruptions in the water supply and the importance of water for survival, putting in a well is a great idea. Of all the possible sources for water, having a well on your own property is the most secure source you can have.This video series shows step by step the build of a Homemade Deep Well Water Pump.Even so, if the grid goes down, that water could be out of your reach, if you don’t take the right precautions.

Watch the DIY Homemade Emergency Deep Well Water Pump series



RECENT POSTS YOU MIGHT LIKE
  • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
    This project goes over the build of an Archimedes Turbine that can generate off the grid power from a flowing river or creek. This is basically a screw that turns when water passes through the pipe. You need a 5 foot farming auger to build this. The farming auger is put inside of a 6 inch pipe and placed in the creek at a certain angle, water would pour into the auger and that water would weigh down that auger and turn it. And so as it turned, it would turn a shaft that is attached to the end of the pipe and run a pulley system with a motor to generate electricity. We take an old belt sander and shave some of the edges to make it smooth and rotate without any friction inside the pipe. We use an angle grinder to split the pipe down the middle and use the separator nuts to kind of give more space in the pipe. Make sure you don't split the pipe into two. Open up enough space on the top by heating the PVC and clamp 2 spacer boards on either side and stretch the opening by using a C clamp. 2 three quarter inch boards are bolted using carriage bolts on either side of the pipe which gives us enough room here to get the auger installed. Allthreads of size eight and quarter inches are put through the boards and secured in place with the help of some washers and non locking nuts. https://www.youtube.com/watch?v=GTD5Y7EyK00 https://www.youtube.com/watch?v=GTD5Y7EyK00 https://www.youtube.com/watch?v=jwIfrIgVqZc https://www.youtube.com/watch?v=veb6xTz7Vhg https://www.youtube.com/watch?v=Ul76_kG0xyI https://www.youtube.com/watch?v=v4I9Zfp62F8 https://www.youtube.com/watch?v=Oqt38fbsQaA
  • DIY Video: How to build a really efficient Portable Ammo Box Wood Stove
    This video shows the build of a really efficient Portable Ammo Box Wood Stove .Great for outdoorsmen, adventurers, preppers, survivalist and anyone looking for a small, portable stove for both heating and cooking. Plus, it's a fun project and makes a great gift for the outdoor enthusiast or hobbyist. The materials needed for this project are 50 Cal Ammo Box,Stove Rope Kit,Propane cylinder,Fiberglass Cloth,Mica Sheet,12" Steel Tent Stakes, 4mm thick steel plate,22 gauge steel sheet,16 gauge, Steel rivets ,BBQ skewer,4 copper pennies,2 small compression springs,3 ½” hose clamp.  

    Watch the Portable Ammo Box Wood Stove Build Series

    Other Articles:
  • How to convert an Old Ceiling Fan Motor into a 70W Efficient Single Phase Alternator Generator
    This project goes over the conversion of an old ceiling fan motor into an single phase alternator .You can't take your standard AC electric motor and spin it and get an electrical current out of it unless you modify it. The ceiling fan motor used here will produce about 70 volts at one amp which is roughly 70 watts. Through a bridge rectifier we can get about 70 watts of power out of it. We start by pulling the cover of the fan. Inside we have a squirrel cage rotor in the middle and 6 coil windings around it. The coil windings are placed in clockwise and anti-clock wise directions inside the stator. Next we remove the circular rotor from the threaded shaft which is attached to it with help of a vice. We attach the shaft with the rotor through it within a vice. With the help of an extra piece of pipe to give leverage, we press them against the rotor and push it away from the rod and pop it off. We are replacing the rotor that we have detached from the shaft with a two inch hex steel bar . It has six sides that matches with the six coils from the stator. With the help of one eighth inch drill bit we cut a hole in the center of our hex bar. We put the hex bar through the shaft and fit them snugly around the threaded area. We take six one half inch neodymium or rare earth magnets and place them along the the 6 sides of the hex bar. We place them in such a manner that the poles of the magnets are opposing each other. For permanent usage, wrap this with a little bit of tape or glue so that they are held in place securely. We place our modified rotor in the middle of the stator and align them such that they fit in tightly. The outer screen is bolted back onto the motor. We can also add second set of magnets to increase the magnetic field of the rotor .This will also bring it closer to the coils on the outside and increase the overall voltage. To convert the alternating current generated by our ceiling fan alternator to direct current, we use a bridge rectifier. It has 4 poles, 2 for connecting our alternating current, the other plus and negative for DC power. https://www.youtube.com/watch?v=k-4IbLOZwnA