How to build an Emergency Deep Well Water Pump from scratch.Step by step build Instructions







RECENT POSTS YOU MIGHT LIKE
  • How to build a really powerful Solar Powered BullDozer that requires no fuel.Step by step Build Instructions
    This video series shows the step by step build of an awesome 275 Watt Solar Powered BullDozer from start to finish.The Solar panels are connected to 4 golf cart batteries that powers a 1 and half HP motor,which again are connected to a bunch of gears and sprockets that independently power each of the 4 wheels to get the maximum traction.Even with 10% power,this bulldozer works like a champ.Another feature of this dozer is easy to control manual steering mechanism.The body is build out of Aluminium/Stainless Steel.The cool thing about this bulldozer is that it runs without Gasoline.Yep no gas needed .ever!!

    Watch the DIY Homemade Solar Powered BullDozer Build Series

  • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
    This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
    Watch the homemade Micro hydro Turbine Build and setup

  • DIY Video : How to recycle your Waste motor oil,transmission oil or any waste fuel into 100% Re-Usable Fuel
    This video shows you How to recycle your Waste motor oil,transmission oil or any waste fuel into 100% Re-Usable Fuel.Instead of throwing away that used motor oil and fuel, you can reuse it. By using a centrifuge, you will be able to extract all of the impurities out from the fuel using centrifugal force. It is more effective that a filter in getting the micro-particles out, and it is completely safe to reuse in your vehicle. The materials needed for this project are Motor Oil - You will be using the centrifuge to convert used waste motor oil to clean fuel that you can reuse,Centrifuge - This will spin the motor oil and extract the impurities from it.Buckets - You will use the buckets to collect the waste and cleaned motor oil. Generator - The centrifuge will use a lot of power. You are going to need a generator in order to run it. Typically, 220 V will be enough to run the centrifuge.Spatula - You will use the spatula to clean the centrifuge and get all of the leftover gunk out of the cylinder to prepare it for another use.

     

    Watch the waste motor oil recycling video