DIY Video : How to build an Off Grid DIY 12 Volt Washing Machine from junk parts and pieces laying around

     

     



    RECENT POSTS YOU MIGHT LIKE
    • How to make a Survival Rope Making Machine at home from easily available materials
      This project goes over the build of a Homemade rope making machine using a simple cordless power drill and some inexpensive materials that are sourced from the local hardware store. Here are the materials needed for this project: Three quarter inch by five inch eye bolts with hex nuts Fender Washers Cut Washers Hex Nuts Plastic Castor Wheels two by two and one by six by six piece of lumber Old bicycle tire tubes Take the board and cut it to length of seven and a half inches and took the first piece and doubled it over the second one and cut them together so that they are exactly the same length. Then I took a piece of two by two and cut it eight and a half inches long. Take large fender washers and position them on the board forming a triangle, you want to do it in such a way so when you add your two by two to the top as well as the bottom, it has similar spacing at the top and the bottom. Put the two boards together, mark the centers and drill the holes. Next step is to build the metal spinning hooks. These spinning hooks are going to be made out of eyebolts which is used as a hook to put the strings on. We take 3 plastic castor wheels and use them as a pulley , connect them together with a small piece of bicycle tire tube so that when one is spun ,all three of them would spin together. We take the 3 eyebolts and push it through the hole and secure them tight with a small cut washer and hex nut. It is locked in place but should spin freely. Put with wheels through the bolts and secure them using fender washers, cut washers and nuts. Take an old used tire tube piece and line it up between the two washers and cut up a piece that is roughly about the same distance as that gap. We loop the tube over the pulley all at once.The Second board is pushed through the bolts over the wheel pulleys.Make sure everything is lined up symmetrically. When we turn one bolt, the belt drives the other two pulleys and they all spin together. As we are running the hook spinner, we are going to need something to hold it at the other end, To make the other end of the mechanism that holds the strings in place, we take six inch piece of common board and eight and a half inches of our two by twos on the bottom to secure it as a base and them we clamp it over a table. The idea is that as each hook begins to spin, the two cords attached to it will intertwine with each other. And then eventually all three of those cords will mesh together to make a nice three stranded rope. As the strands are twisted, it creates tension on the backboard. To relieve the tension, we drill a hole through the backboard and tie the rope to another counterweight rope through a swivel hook that pulls the tension and allows it to rise as the cord is pulled. We also make a rope makers top that will help guide those strands into the beautiful three strand cord. We add two ropes between the spinner mechanism as guidelines and connect it to the back board to accommodate the rope makers top. The idea is that as the tension builds it will glide forward and guide the individual strands into place to form a three stranded rope. We sandpaper the holes on the rope makers top to make it smoother so that the lines won't snag up when they start twisting. We put a wooden knob on the back to reduce the friction so that the rope makers top can slide smoothly. Loop the cords through each of the three hooks on our rope maker machine .Form a slipknot and connect it to the swivel hook. We have our rope machine build complete . To tie and cut of the rope, take a small piece of electrical tape and wrap it around the end where you want to cut it off. Cut The Rope at the back just where the electrical tape ends . https://www.youtube.com/watch?v=ddenqErLL0Q https://www.youtube.com/watch?v=uEvM6ue3L7E https://www.youtube.com/watch?v=RM9GY-n6PEA
    • How to build a Simple Alternative Power Dual Refrigeration System that uses no electricity
      This project goes over the conversion of an old three way refrigerator unit from an RV into an alternative power offgrid Dual refrigeration system that uses no electric power. This can be really useful in case of a power outage or SHTF situation when you need to keep your food or vegetables fresh. The first step is to strip the fittings on the back side of the fridge , remove all the ammonia system ,clean the inside of it . Here we are incorporating more than one way to use this water for cooling refrigeration system to make it efficient .We will be using cooling effect by brining down the water temperature to cool the box , another way to cool the box is by installing an evaporative system. We take the two pipes coming from the water source around the edges of the box and put some cotton sheets around the sides and let the water cascade down the sheet creating an evaporative effect. We have an inverter and a battery attached to the fridge that is hooked up to a 25W solar panel .The wire from the inverter is connected to 8W Electric Fish tank pump .The water coming from the pump goes underneath and up inside to the lid of the fridge to the condenser coils and then comes back around back into the water source like well or water tank. The full system is recirculated back into the original storage tank where the water is coming from. We keep the fridge in a chest freezer style instead of an upright style. Inside the fridge, we have incorporated 2 poly tubing coils attached to an old heat sink that was already in the fridge. The 100ft coils are attached to the top of the fridge. The cold from that coils will drop down to the rest of the fridge. Next step is to incorporate the evaporative cooling part of the refrigeration system. We start by installing aluminum U channels across all the edges of the fridge. The U channel will hold cotton material inside of them. The water coming out of the outputs from our coils rushes into the channel which is going to wick out into the cloth and run down the cloth with gravity, giving us our evaporative cooling effect . On the corners, we have the U channels interconnected to each other through a bent garden hose in such a way that any extra water flow in the channel can transfer to the the channel that is next. The cotton sheets are stretched around the box and tuck it down into the channels all the way around under the wires such that the wires will hold the channels up and hold the sheet up inside the channel. To even the flow of the water ,we install a tee. Now the water coming from both sides of the channel can leak into the sheet. Also make sure you have an air gap between the sheet and the refrigerator box. https://www.youtube.com/watch?v=mHspLgLWJug
    • How to recycle scrap metal in the backyard by building a simple Mini Metal Foundry from start to finish
      In this project, we're using equal parts of sand and plaster to make a simple backyard foundry that's powerful enough to melt scrap metal in seconds. With this homemade furnace, we have the power to liquefy aluminum in the backyard and cast just about any object we can think of. You will need some big bag of play sand and some plaster of paris both of which you can find at your local hardware store for under $20. We are also going to need a 10 quart steel bucket and a tablecloth to cover anything. For this makeshift refractory lining we need One and 1/3 buckets full of plaster Paris or 21 cups, One and 3/4 buckets full of sand or 21 cups and 1 and 1/4 buckets filled with water or 15 cups. Mix everything together. It's really important to get all the dry powder wet and work out any lumps as quickly as possible. And after mixing for a couple of minutes, it should be fairly runny and roughly all the same color. Transfer the mix to the steel bucket upto 3 inches from top. We use the plastic measuring bucket to form the center of the foundry. Let the mixture dry for 3 minutes. Next step ,we turn an old steel fire extinguisher into a custom crucible. Depressurize the tank and unscrewed the valve from the top to make it safe and easy to cut in half with a hacksaw. At this point the plaster should be pretty well set. So let's dump the water from the bucket then use a pair of channel locks to pull the bucket out. Next step is make an air supply port .Using 3/8 inch hole saw and a metal cutting blade, we cut a hole to accommodate the one inch steel blower tube. The blower tube is made of one inch steep pipe ,one inch PVC coupling and one inch PVC pipe.Threads on one half of the coupling screw onto the steel pipe and the slip adapter on the other end simply pushes onto the PVC side easily. Next step is to build a lid to retain the heat.You need a couple of 4 inch U bolts.Make them stand upright into a 5 quart bucket filled with the insulating mix. To relieve pressure buildup, make a vent hole using a 3 inch hole cutting saw. This design works great for venting pressure and gives us the option to melt metal as well without even having to take the lid off the furnace. By the way, if you run out of soda cans to melt, you could try using it as a blacksmithing forge or even a barbecue for summertime grilling. We evenly place 5 charcoal briquettes at the bottom of the crucible made out of steel fire extinguisher, helps smelt the can faster once we fire it up. A hair dryer is taped to a PVC pipe and inserted a couple of one inch couplings to connect the steel tub eat one end and give the blower to a quick release feature. This way it's super easy to take apart and fits into a five gallon bucket for easy storage. The charcoal is filled it to the top and we breathe life into the steel furnace with a propane torch.The hairdryer is set to the low setting and blow a steady stream of oxygen on the charcoal to really heat things up. The lid we made keeps the heat inside so it conserves energy while it's bringing up the temperature. The coolest part is that the crucible lines up perfectly with the hole in the center. The container is three inches wide, which is the perfect size for melting standard size soda cans like these and at temperatures over 1000 degrees Fahrenheit . In order to isolate aluminium, first we remove the crucible making sure we have got a very secure grip with our tongs and slowly pour the liquid into a steel mold. The Soda cans are molded in the form of ingots.The purpose of an ingot is to keep some pure metal handy for when you want to make something cool. https://www.youtube.com/watch?v=hHD10DjxM1g https://www.youtube.com/watch?v=lSoWxG30rb0