How to generate Free and Emergency hot water for your house by building a Waste Oil powered water heater



This Video shows the build of a water heater from an old gas hot water service and converted it to run on waste oil instead of gas.The system could easily be set up in an off grid or prepper type location as it only needs a small amount of 12V power to supply the car blower I used here. The burner runs on any waste oil and is gravity fed without the need for Nozzles, pumps or compressors. As well as providing Domestic hot water, the output can also be used in a home heating system which is what I plan to set up for my home this winter.It could also be used for an outdoor shower, to heat water for animal troughs, to heat a spa or small swimming pool or other uses to replace gas or electric how water heating.

Watch the DIY Homemade Waste Oil powered Water Heater Build



RECENT POSTS YOU MIGHT LIKE
  • DIY Videos :How to generate Free Power for the rest of your life by building a Micro Hydro Electric Power system and kiss the Grid system goodbye.
    This 16 part Awesome Video series shows the overview and setup in detail of a Micro Hydro Electric Power System build for the long term from the ground up.What a hydroelectric system does is that it converts the force from flowing water into electricity. You take the kinetic energy of water flowing downhill from a stream or river and direct it onto a wheel in a turbine that converts the rotational energy to electricity. I have 2 natural springs that provide water which falls about 500 vertical feet through a mile of pipe and develops about 220 psi..Harness the power of hydropower; flowing water for clean, sustainable home free electricity 24/7 and ditch your dependency on the grid system for good. [the_ad id="6435"] The basic components of this build are A Stream Of Flowing Water - A hydroelectric generator is only useful in a bed of flowing water,Magnets - The magnets will spin against the coils to create an electric current.Bearing - Used for the disc to spin against,Coils - The coils will spin against the bank is to create an electric current.Half-Inch PVC Pipe - The disc will be placed on the PVC pipe.5-gallon bucket,Waterline - We are using the 5-gallon bucket and waterline to create a closed system. The overview of the steps mentioned in this video series: The first step in creating your hydroelectric generator is to create the discs. There are two parts to the disc, the stator and rotator disc. The stator disk is stationary and contains the coils. The rotator disc will be spun using the water current. The magnets will spin against the coils, creating an electric current. Now that we know the process, it is time to learn how you can make a hydroelectric generator yourself. You can create these discs using templates that you can find online. Trace the amount uncovered and use them as templates to cut the discs that you will be using. Make a hole in the discs ½ inch wide, so the half-inch PVC pipe can fit through the center of them. Place the discs side-by-side and attach the fins to the turbine. Attach the turbine to the rotator disc so it spins as the turbine spins. Make sure the fins are facing into the flow of water so that they will be pushed as the water passes through them. Next, attach the coils to the stator and at the magnets to the rotator disc. When you add the magnets, alternate them with their North and South poles. Make sure each north facing magnet is next to two south facing magnets. Likewise, make sure each south facing magnet is next to two north facing magnets. Add the turbine, rotator disc, and stator disk to the PVC pipe and rest it on top of the bucket. Pour water over The fins and the turbine will begin spinning. As the turbine spins, it will begin producing current as the bank is passed across the coils.
    Watch the step by step Micro Hydro Electric Power station Build Series

  • DIY Video : How Generate Unlimited Hot water without electricity by building a Homemade Underwater Wood Stove
    This video shows the generation of Unlimited hot water  100% Off the Grid without electricity by converting an old propane tank to burn underwater as an immersion heater for a lot of hot water.Here,I use a homemade underwater wood stove to make a lot of hot water in a relatively short time.I also make use of the waste heat to cook breakfast.Almost 75-80 gallons of hot water in 1 hour with wood.Really a great way to heat a lot of water.

    Watch the DIY Homemade Underwater Wood Stove Water Heater build

  • DIY Video : How to build a 100W Super Bright LED Flashlight using a PVC pipe and Dead Laptop Battery
    This video shows the build of a super bright 100W LED flashlight in PVC pipe housing.Main parts bought from ebay. The battery of this flashlight came from 18650 lithium cells removed from dead laptop batteries.The other materials required for this build are 100W LED COB chip,100W LED Reflector, lens, lens bracket kit,DC to DC boost converter 250W,DC to DC step down (buck) converter.Some parts bought at local electronics or hardware store.Rest all stuff had lying around.The other video shows the build of the 22V 6Ah battery pack from dead laptop batteries.

    Watch the DIY Homemade 100W LED Flashlight using PVC and Laptop Battery Build