DIY Video : How to build an Awesome WaterJet Cutter at Home for Dirt Cheap .Build The Ultimate Cutting Tool



    RECENT POSTS YOU MIGHT LIKE
    • DIY Video :How to build your own Homemade Lumber Mill from Scratch .
      This projects goes over the build of a cheap homemade lumber mill using materials around your home This mill has a 12 inch saw blade purchased from Home Depot that cab do cross cuts, or it can do longitudinal rip cut.I am gonna be cutting the long direction on the word. First step is building the rollers. Four rollers are made out scrap materials lying around. The wheels are made of polycarbonate material .These are adjusted on a drill to ensure that they roll smoothly on the pipes. Next step is the build the tracks.Here I use 2 old steel pipes and welded to make a long one. 3 more pipes are welded on top of those 2 long pipes horizontally to give stability. Make sure the pipes are all lined up . 2 rolling carts are made from the leftover pipes tha slides across the pipes.Make sure these are parallel to each other.4 sliding pipes are bolted on these carts. 4 pieces of pipes are welded on top of these rolling pipes that are paralled to the horizontal pipes below .They act as a crank that can pull the sliding pipes. Threaded holes are put along the pipe that connects the sliding pipes.2 cables are connected in opposite ways to a small spring pulley system that can help sliding pipes move vertically up and down when the top crank is rotated. The Saw Blade is attached to a steel rod.The blade is attached to a washer on the other side to ensure it doesn't fly off. The axle is passed through a square metal box which is bolted using a bearing on both sides. The motors attaches to the top of the box mount .A pulley is then attached to the metal rod from the motor using a small wheel. The next step is to take whole side assembly thing attach it to the cart so it can pivot. Ball bearings are attached to the box on both sides.This must be placed at a very specific distance away from the blade. So that when I flip it the the edge of the blade will line up so it cuts clean without cutting deeper into the wood and without not cutting far enough and leaving it still attached.When its swiveled it will pivot the blade perfectly. Next step is make take the whole motor and blade assembly and attach it to our rails so that it can slide and rotate . We attached 2 pieces on both sides of the motor blade assembly to ensure that the system stays perfectly straight while cutting horizontal or vertical. https://www.youtube.com/watch?v=KtL7LoFeTyg https://www.youtube.com/watch?v=txUgR7kYpgI https://www.youtube.com/watch?v=LUxo36NebVA https://www.youtube.com/watch?v=IOEHT1UrbKM https://www.youtube.com/watch?v=deblj68KZug https://www.youtube.com/watch?v=Axo2w5_qHd8 https://www.youtube.com/watch?v=_uhvSBLY0Xc https://www.youtube.com/watch?v=5sPu_TcUtyU
    • DIY Video : How to build a Simple Woodgas generator for small electric RV generator
      This is the build of a simple Wood gas generator for small 5HP electric generator.This is made from simple materials that can be easily found around your home. The main generator here is a 20 gallon garbage can inside I have a wine cooler and inside there I have hung a small steel bowl. It's just connected up to this very long aluminum duck line to my filter and my filter has been filled with wood pellets to also serve as the fuel. . Then the outlet line goes over to an air inlet port.When you burn the gas you have to add air and this is the valve I've designed to allow that. It goes all the way to the RV Gas engine.You can cut off the fuel by using a wire to cut off the fuel pump. We use a 20 gallon garbage can as the filter.So first I use a quarter inch drill to put two holes in here and then I've enlarged it with a nibbler.Put a harbour wire down in the can where the filter medium is dumped. I use pine wood shavings as a filter medium.Use about 1/3 to fill up my 20 gallon. The reactor is basically constructed out of a stainless steel thermos, which is a central cylinder that is double walled and it has like a one inch opening at the bottom. And below that we've just hung a steel mixing bowl that we basically drilled a lot of holes into and then hung by these three chains that you have riveted in. And then we just connected it with a simple 20 foot ordinary dryer duct. The reactor is filled up some wood pellets ,we have stretched out the hose, this will cool the gas into the improved 20 gallon filter. And I'm going to be driving this with a small air mattress pump. And what I've done is I've rigged myself a dimmer control here so I can actually control the speed. https://www.youtube.com/watch?v=5WLuZP71dc0 https://www.youtube.com/watch?v=cLUNw4knlkc https://www.youtube.com/watch?v=uz93cb0zPlk
    • DIY Video:How to build a Homemade Double Barrel Garage Heater out of Old Water Tanks .Efficient,clean burn and cheap!
      This project goes over the build of Double Barrel Stove out of two old scrap water heaters for the shop. The first step is to disassemble both the old electric hot water heaters to get their tanks out. Take a grinder and cut a section off from the top of the water heater tank. This tank will become the bottom tank. Remove any calcium and mineral that ends up developing deposits inside the bottom of the tank. Take a 12 gauge plate steel and put our top drum upside down and scribe a circle out of them from the end and cut it. Weld the steel piece onto the drum. You need to do the same for the other drum too because with these double barrels, you are basically making two stoves, just connecting them in the middle. Now both the top tank and bottom tank ends have been polished and cleaned .Remove any insulations, paints and glues from them if they have any. Make sure all the rough pieces on the tank are welded on ground down. Cut a small piece of pipe that acts as stack between the 2 tank. Next step is to add a small support bracket on the top of the bottom tank that will help support the top tank. Cut a hole on the bottom tank .This will be where the stack goes between two of them. Fill the drain plug down at the bottom . Take the top tank, cut and weld the top exhaust stack that will be six inch outlet for the smoke. We also add a six inch inlet that goes up to the top that forces your your smoke and the gas has to go across the length of the barrel. The bottom barrel will be connected to this. Both barrels are welded together, the bottom barrel is welded onto the mid stack which connects the top barrel with the exhaust stack. In order to support the barrels, we take the scrap pipes lying around and make legs as a support structure for the stove. Next is the door fabrication. We cut a hole for the door in the bottom barrel. A couple of hinges, door catch are welded on to this end. An air inlet pipe is threaded onto a plate. The whole unit is then attached to the door. A handle is attached to the inlet pipe so you can open and close whenever you want to control the flow of the air intake. https://www.youtube.com/watch?v=fTj4pjJ4DT0