DIY Video:How to set up a Complete Off the grid living System using Solar and Wind Turbines . Make your own Power and never pay for electricity again.


    This video series shows in detail how to setup a Complete Off the grid living System by using wind and solar to make your own power for everyday living.The series begins with a video that shows a rough back down on a off grid system.The next set of videos shows how to set up a Wind turbine ,solar system and an off grid hot water system along with managing the batteries.This is great for folks who are tired of the government ripping them apart and those who would like to escape the city life and enjoy real life around the woods,mountains and the rivers.Setting up a good off-grid system is the best option for receiving energy from both wind and sun. This is the most practical alternative as you may reuse and maximize the utilization of resources.

    Watch the DIY Complete Off the grid living System Setup Video series



    RECENT POSTS YOU MIGHT LIKE
    • DIY Video: How to build a Band Sawmill from scratch in your backyard and save a lot of money. Step by step build instructions.
      This video series shows the step by step build of a homemade Band Sawmill from scratch in your backyard.Harvesting and processing the wood that grows on your property is the dream of many homesteaders. The dream can be expensive (around $5k) because you need a sawmill in order to rip the wood and remove the bark.Instead of spending years saving up, you can spend less by building your own saw mill.it’s a tool you’ll use for years to come, and will more than pay for itself the first time you use it. Lumber isn’t cheap, and if you’ve got the natural resources and access to those resources, it makes the most sense to save money, time, and effort by using what you have available.

      Watch the DIY step by step build of the Band Sawmill series

    • How to run a Homemade Generator on Wood or even Trash/Garbage
      This video series shows how you can run a generator on wood or even trash.When wood is heated it releases a few different types of gases, I use a homemade gasifier to extract these gases out of the wood, I first run the gas through a condenser coil to condense any steam and tar out of the gas, I then use a bubble filter to catch that water and tar and it also helps in filtering out some of the unwanted smoke, next the gas runs through a homemade filter to remove the last of the unwanted byproducts, The wood gas then runs directly into the air intake on the 25cc engine.

      Watch the DIY Homemade Wood Gasifier Build Video

    • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
      This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
      Watch the homemade Micro hydro Turbine Build and setup