DIY Video:How To Turn Your Old Fan Into An Airconditioner AC for cheap.

If you are looking for an inexpensive way to beat the heat this summer, there are plenty of very effective DIY options you can try.One of option is to turn an old fan into a Airconditioner AC .The materials you need for the build are 15 foot roll of 1/4″ Copper tube,(2) 3/8″ clear vinyl tubing cut to length needed,(2) hose clamps that fit the outer diameter of the vinyl tubing.A bag of short zip ties or cable ties (get a bag of 100 they don’t cost much).Even before our society arrives at a complete meltdown, summer cooling bills can easily leave you with little money for daily needs and prepping

Watch the DIY Homemade Fan converted Air Conditioner AC build video

 



RECENT POSTS YOU MIGHT LIKE
  • DIY Video : How to build a Homemade Atmospheric Water Generator . Produces/Extracts Distilled Water from the air
    This video shows the build of a Homemade DIY Atmospheric Water Generator!.ThisUnit pulls Pure 'distilled water' straight out of the air. This simple design pumps near freezing water thru a long section of copper coil. Coil becomes very cold and dew (condensate) forms on the coil. The dew is then caught by a drip-pan located beneath the coil.This unit has the added benefit of dehumidifying the air.I used only aluminum and copper in this version. main thing with these is to keep the coils clean. if coils are cleaned after each use, the water generated is 'distilled water.

    Watch the DIY Homemade Atmospheric Water Generator Build Video here

  • DIY Video : How to build a Powerful Mini Box fan for or off-grid use, camping, emergencies or everyday use
    This Video shows the build of a Homemade 12VDC Mini Box Fan! w/motor speed control!Powered with a 12v battery or 12v solar panel! Made Sturdy and is SUPER POWERFUL! pushes more air than a fan twice its size.Ithas a whopping 1500 CFM air-flow volume with wind speeds measuring in at over 20 MPH! (32 kph) and with the motor control switch you can set it to run at any of 100 different speeds! .Great for off-grid use, camping, emergencies or everyday use. tip: run it from a cars' 12v cigarette lighter plug.

    Watch the DIY Homemade 12VDC Mini Box Fan Build Video

  • How to build a Homemade Archimedes Screw Turbine using PVC parts to generate Off the grid Power from a flowing river or stream/creek
    This video series shows the setup of a micro hydro system using a flume which is basically a water trough that carries water to some height so the water can fall.The water enters the screw at the top and the weight of the water pushes on the helical flights, allowing the water to fall to the lower level and causing the screw to rotate.This rotational energy can then be extracted by an electrical generator connected to the main shaft of the screw. The materials you need to build this are Four decking boards - To serve as the floor in size to direct the water. Two 2x4’s – These will be cut to provide support for the decking boards,Screws - To secure the boards in place.6” PVC Pipe – Used as the body casing,Flange Bering – To spin the turbine,PVC T-Joint – Serves as the opening to let water flow through it,Farm Auger – This will spin as the water flows through it. Building the flume is a simple process, but it may take a lot of work depending on how far you need to take the water. We will show you how to build one section of the flume. From there, you can replicate this and make the flume as long as you need to. Take your 2x4’s and cut out two pieces that are 22 inches long, two pieces that are 17 inches long, and four pieces that are 8 inches long. Start out by laying the three 22 inch pieces horizontally and place two decking boards on top of them. Take the other two decking boards and use them as the side barriers for the water. Attach the four 8 inch pieces on either side of the supports and use the 17-inch pieces as cross supports over top of the flume. This is the completed section of the flume. Continue to replicate this and add to the flume as needed. You can attach stilts to the bottom of the flume to angle it downwards for the water to flow through it. Building the Archimedes screw turbine is simple. To start, simply take your PVC pipe and attach the pieces together. Since this is only a four-piece setup, it is very straightforward to set up. Insert the auger and make sure it has room to spin without too much friction slowing it down. Once the Archimedes screw turbine is put together, bring it to your flume and you can begin using it. Situate the flume so that it is creating a waterfall that you can position the screw turbine underneath. As water flows into the turbine, it will spin it. You can use this force to generate electricity. One of the great things about this setup is that it never stops. For as long as you have running water in the area, you will be able to generate electricity with this setup.
    Watch the homemade Micro hydro Turbine Build and setup