DIY Video : How to build a 100W Super Bright LED Flashlight using a PVC pipe and Dead Laptop Battery



    RECENT POSTS YOU MIGHT LIKE
    • DIY Video : How to heat your Garage by using an Outdoor Wood Burning Boiler and an old car radiator
      This video shows a home-made outdoor wood burning boiler system used to heat a garage.This uses an indoor car radiator and fan and some underground tubing to cycle the water through.The materials you need for this build are a Barrel Stove kit,Pex crimper,Pex tubing,Pex clamps,Windows Fan,Coolant and a Submersible Pump.

      Watch the Garage Heater build Videos

    • How to build a Homemade Copper Pipe Solar Water Heater and get super hot water fast and free
      This project goes over the build of a Homemade Copper Pipe Solar Thermal Water heater which can produce super hot water fast .This reaches temperature at or above 150F with air temperature from high 40's to low 50's. Here are the materials needed for this project are : Two 10 foot half inch copper pipes - Type L 16 half inch 90 degree elbows 18 tube straps 23 X 35 half inch plywood for the back 18 X 20 half inch plywood for the pipe support 2 X 2 lumber at 20 and 35" for the sides 4 and 3/8 inch square dowel rods for the glass support 1/2 inch threaded pipe adapter 3/4" to 1/2" garden hose PVC adapter 1/2 inch coupler. The first step is to cut down a bunch of two foot sections out of the 10 foot sections using a copper cutter. We cut 7 of them and 2 more for the top and bottom which are 30 inches each. Next we cut 8 sections of 1 1/8" for the connecter pieces between elbow joints. This allows the pipe to be spaced exactly two inches apart on the board evenly all the way up and down Connect the pipes using couple of elbows and a 2 inch connecter piece and solder them .Do it for the rest of the pipes. Slide the pipes into the plywood frame collector and fasten them onto it using 3/8 inch screws to be more secure. A small internal board is placed onto this frame which helps the pipe to lay flat inside .Also it holds the pipe at right height so that it exits through the right holes. It allows for the pipe to be easily removed from the collector frame. Cut the wooden dowel rods and put inside the collector to support the glass. Sand them a little bit so that the copper pipe will fit back through. A straight coupler is welded on to the end of outlet then you can add any pipe or connecter or wherever you want the water to go. The inner board is secured to the back board using some three quarter inch screws. The 4 corners of the 2 X 2 wood frame is secured using 2 and half inch wood screws and the corners of the back board is secured by one and one half inch screws. A 20 X 32 inch glass is placed on the frame with the help of some silicone caulk around the edge. The highest piece of copper in there is eighth of an inch away from the glass and its painted black. https://www.youtube.com/watch?v=7uOQEXmyHRs
    • DIY Video:How to build a Simple Homemade Pocket Straw Style Water Filter. Small, lightweight and powerful.
      This project goes over the build of an emergency Straw Style Survival Water Filter. This water filter is small, lightweight and ideal for an SHTF scenario or hiking/camping. Very effective for purifying rain or tap water or removing disease causing water contaminants. With regular maintenance the filter should last for years. The materials needed to make this water filter are turkey baster , cotton balls, coffee filters,activated carbon. All these materials can be purchased from your local store or aquarium supply stores. The activated carbon is rated to last for five months if used regularly. Start by taking a cotton ball and push it down the turkey baster. Rinse the activated carbon by running it through tap water before putting them over the cotton balls. Pour the rinsed activated carbon all the way to the top of the pipe and put two more cotton balls at the top . Now take some coffee filter paper and slide it over the top of the cotton balls and tie it down using a twist tie or rubber band so that the whole thing wont slip out when you are using it. If you don't have the cotton balls available, you can always just ball up some pieces of coffee filter paper and put them on either end of the activated carbon in between. An alternative way of using this is to cut the top of the poultry baster and and put it on the top of the straw . Take the dirty water and manually filter it through the straw. Once the material inside the filter gets saturated water moves pretty thoroughly through the straw. The cotton balls in the paper will get dirty pretty quick up here capturing most of the dirt but you can just pull those out periodically and add new ones. https://www.youtube.com/watch?v=zXJypLXwsiw