DIY Video: How to build a Homemade Hot Water Off grid Air Heater using Heat Exchanger and a Car Radiator Fan

     



    RECENT POSTS YOU MIGHT LIKE
    • How to build a Homemade Wooden Bandsaw Mill from Scratch.Step by step build Instructions
      This project goes over the build of a simple Homemade Bandsaw mill that can that turn hard maple into smaller lumber . The first step is to make the wheels of the mill. Here we use a three quarter MDF board to make this. The wheel size is 16 inch. We use a beam compass to cut circles and cut two wheels out of them. We make a seven and half pulley for the wheel using a three quarter inch plywood and drill a five eighth inch hole into the middle where the shaft goes. We take some hot melt glue and glue the stock collar onto the pulley and tighten it with a set screw so as to stop it from spinning. Before joining the wheel and pulley together, we make another small disc to go in between to act as a spacer .We glue the pulley to this spacer and from spacer to the wheel. Two wheel bearing blocks are bolted to the wheel on both sides using 4 three eighth inch threaded rods. Make sure that the threaded rods are tight inside the hole in the wheel, but the bearing blocks itself can move around. One way to keep these bearing blocks in place so that they dont move side to side is to apply some construction adhesive to the corners. Next step is building the frame for the saw from salvaged 2 X 4 boards. Make sure that the 2X 4's are straight. Take the bench hand plane and smoothen the edges so that the boards sit flat. It takes several shallow passes flipping the woods each time to get rid of all the twists and warps. Two frames pieces hold the wheel in ,the stationary drive wheel is placed eight and half inches from the end. Two five eighth inch holes are drilled on both the frames so that axles fits in there neatly. On the other side, one holes are drilled that gives the room to adjust the wheel. We also make an adjustment collar out of plywood that is bolted into the frame and the shaft . The collar can be moved to adjust the wheel. We also place couple of pieces across the frame and secure them tight so that the supporting boards are locked in position. On the other side we install the front wheel or top wheel. This wheel needs to move back and forth to put tension on the blade. It also must have a tracking mechanism. For that we make a two small piece that locks into the shaft on the front wheel and slides back and fourth. A guide piece is drilled onto to this piece . A one inch hole is drilled into our slider piece and a three eighth inch threaded rod is secured in there with a nut and washer. These rods help put tension on the blade and also adjusts tracking. Before putting the blades on the wheels, we put silicone caulking on the wheels to smoothen it out .These have advantage over bicycle inner tubes as it doesn't drape down over. The legs are attached to the frame using gusset blocks. To put the motor onto the frame , we take a melamine board and screw them aside the stationary wheel using a cross board. This piece of melamine not only supports the motor, it also helps to brace up the top to keep that from rocking. Secure them tight so that it resists moving while the cutting is going on. Next we make blade guides near the bottom to make a guard for the blades just in case it snaps and flies off. The blade guides are made of small piece of steel angle that is glued to a ceramic piece. The way blade guides work is that they don't actually touch the blade when it is running. It is only when the blade tries to move up or down that it will constrain it and keep it on track and prevent it from twisting. A thrust bearing made of regular size ball bearings is bolted onto an aluminum angle that is further attached to the blade guide. We make a dolly cart out of 2 X 4 boards and some castors to place the big maple logs and move it effortlessly through the blades . The castors are screwed in the ends using quarter inch holes. The castors are fixed in such a way that it moves only in one direction back and forth. https://www.youtube.com/watch?v=rhFEVf8zZkg&list=PLQl9KPrpiIH9Sk0wEiN9d0ANUOK-ntV-i
    • DIY Video :How to heat your Home by building an Smokeless Outdoor Wood Boiler from Start to finish
      This video series shows the build of a smokeless wood burning boiler from start to finish.It is built from a old hot water tank and a small air compressor tank and costs next to nothing to build.The first video of the seriesĀ  will show the construction of the boiler itself. The next video will detail how to hook it up to a pump and exchanger to bring the heat inside. The final video will show modifications I make to the stove to make it even more efficient.

      Watch the build of a Homemade Smokeless Outdoor Wood Video Series

    • How to build your own 24 X 24 Garage and save money. Step by Step Build Instructions
      This tutorial goes over the basic overview of a 24x24 , two 9 foot door,one side door window garage.First of all,you will need to take permission from the building inspector.The inspector makes sure that you are within zoning requirements.You will need the paperwork ,plot plan when you go to the building inspector and those are available from your assessor's office or the town hall or you may have one with your deed.Started with a bucket loader come in, take out some trees level off the area remove blushes and prep for the concrete work. The first step is to dig down and install the footings where the wall is kind of set.Here I have a four foot wall put in with the floating floor. Wall of the foundation is about six inches high, it goes into the ground four foot.And one reason that I wanted the wall foundation versus a flat pad foundation is because of the bug issues. After the footings are dry in a few days,the walls are put up and I have the openings for the two nine foot doors and a side door. After they dry for a few days,the floor screen is laid .This is a standard 4 inch thick flooring. Floating floor means that in reality, if the ground swells during the winter time, the floor can actually rise up and sink down. But it prevents it from cracking because it does have a little give to it. So it's not actually connected to this wall. It's poured right up against it, but the floor is a separate piece by itself. When the walls are poured every four foot they have a half inch threaded rod that's embedded into the concrete while it's still wet, it goes down about maybe a foot and a half has an L shape on the bottom in the rod will stick up directly in the center of the 2 X 4. 2 inlets for underground wiring,a 50 and 130 amp circuit.Its buried four foot down through the PVC. The walls are standard 2 X 4, a double sill plate and a top plate those are the two that run horizontally. I use pressure treated against the concrete which will take care of the bug issues. The headers for the garage door is standrd 2X10,double up half inch plywood in the center. The plywood on the three sides and trusses are put up.The trusses are put upside down and they are flipped up.But once they're up there I marked the top sills where I wanted them nailed them and put braces across the top,measure and straighten them out. The first truss on the end of the building on both ends is called the gable end. It's a little different than the other main trusses.The trusses are 24 inch on center, which means that they're spaced 24 inches apart,unlike the walls which are 16. The roof and the sides are on half inch plywood.I also run some stringers down the center and off to the sides to help so they won't twist during a snowstorm.One thing that's very important is when you put up the plywood the very first piece that you put on is the most important piece of wood that you're going to put on this garage because everything references off that one piece.It has to be square to the gable end . When the first piece of plywood is put up, you install the plywood ties between the trusses and all that does is if the roof gets moisture from inside the garage,it will tend to flex.The ties help in keeping them nice and flat and avoid the bowing. The truss catwalk goes right down the center that stabilizes the horizontal bottom piece of the truss. The doors are framed and roof is made of standard architectural shingles.These shingles have more lifespan.Also added tarpaper on the roof.The wiring is through down the center of the catwalk. The finished garage and the build videos