How to build a Simple Homemade Bandsaw Mill from Old Car Wheels

[the_ad id=”6432″]
This video shows the build of an really inexpensive homemade bandsaw mill out of old car wheels.One of the best things about this design is it’s simplicity of course, but it’s also made from salvaged and repurposed materials, which helps cut the cost of the sawmill down to an affordable level. Not everyone can afford $4000 to $5000 for a brand new portable sawmill. Building your own sawmill not only gives you that sense of satisfaction of doing it yourself, but it saves you money.Bottom line, it’s a tool you’ll use for years to come, and will more than pay for itself the first time you use it. Lumber isn’t cheap, and if you’ve got the natural resources and access to those resources, it makes the most sense to save money, time, and effort by using what you have available

Watch the DIY Homemade Bandsaw mill from Old Car Wheels Build Video



RECENT POSTS YOU MIGHT LIKE
  • DIY Video:How to build a Super Efficient Rocket Mass Heater from reclaimed and repurposed items and save up to 80% on your heating bills
    This video series shows the build of a one of kind Rocket Mass heater.This heater uses  aerate concrete and keep the 'mass' of the rocket mass heater light. This heater goes together like an erector set, and comes apart just as easily. It's custom exhaust can be rotated 180 degrees in any direction, and can be routed through a mass bench as well as its custom mini mass. This heater can save you up to 80% on your heating bills.This heater is beautiful and built completely from reclaimed and repurposed items. The advantage of this type of rocket mass heater is the huge increase in the efficiency of capturing and storing the available heat.

    Watch the DIY Homemade Rocket Mass heater Build Videos from start to finish

  • DIY Video:How to build an awesome Roof Top Portable ABS Pipe Hot Water Heater/Shower . Great for Camping/ Outdoors
    This video shows the build of a DIY solar powered, pressurized, roof top water heater and shower.This is done using an ABS 4 inch pipe, 6 feet long, which would give me a capacity of 15 Litres or 4 US gallons.This is an easy and inexpensive project that required minimal tools and just some basic plumbing parts.I started by installing the shutoff valve. I wanted the drain to be as low as possible in the pipe to avoid necessity of having to tilt the system. To ensure the valve retaining nut did not interfere with the pipe once it is glued into the, I positioned the nut away from the wall of the cap using a bolt, which is the same thickness as the wall of the pipe.I drilled out a 2” threaded cap and tapped in a radiator valve drain plug that I picked up at the local automotive parts store. This valve will allow me to release pressure from the tank should that be necessary without opening the drain shutoff. Also when open, this will allow a gravity fed system through the drain valve should for some reason I not have access to the air compressor.As a final step to improve thermal absorption of solar energy, I painted the surface with flat black paint. First I lightly buffed all the ABS surfaces with steel wool soaked Methol Hydrate. Then applied one coat of spray primer followed by two coats of flat black paint.

    Watch the DIY Homemade Inexpensive Roof top Solar ABS Pipe Hot Water System Build Video

  • DIY Video : How to build a Thermal siphoning rocket stove for an off grid water system. Clean and efficient burn
    This Video shows the build of a Thermal siphoning rocket stove for an off grid water system. The advantage of the rocket stove is a clean and efficient burn. This system uses 5 metres of 20mm annealed copper pipe, and though I designed the rocket in a J configuration, it worked better as a batch box. There is a vortex generator at the base of the riser and basically I was able to heat 200 litres of cool water straight out of the tap to 67 degrees Celcius / 152.7 F in 1.5 hrs.

    Watch the DIY Thermal siphoning rocket stove build Video