DIY Video :How to build a Wood Stove that runs a generator, produces gasoline,runs a fridge and act as a water heater at the same time

This Video shows one of the most efficient wood stove on the planet it will make gasoline run a generator and a propane fridge, heats hot water and your home at the same time.This Stove can burn all paper and plastic trash, cow dung, wood, grass and even dry human waste plus just about every other dry organic compound. The bio-digester manure can be burnt after it produces methane for you and used as Syn-Gas.To construct a perfect wood stove, you have to collect all the important components, with which the device should be built up. You’ll need Barrel,Stovepipe,Driller,Braces,Welding gloves.Generally, it is said that the efficiency of wood may vary from one model to another. However, still, with the above method, you can design the best stove, which can not only operate a generator and fridge but also forms gasoline. If your stove is in hotter condition, it may be easier to break down the fuel into smaller particles at the time of burning.

Watch the homemade DIY Multipurpose Wood Stove build Video



RECENT POSTS YOU MIGHT LIKE
  • DIY Video: How to build an efficient rocket mass heater from scraps for your garage
    This Video series shows the build of an efficient rocket mass heater from scraps for your garage.This  rocket mass heater is the ultra high efficiency, mass based, thermal storage, chambered combustion, for internal energy dissipation, causing time released electromagnetic radiation, and conduction of energy, heating system.Not only do they provide your home with wonderful warmth but they can also heat your home at a fraction of the cost and without leaving that harmful carbon footprint. Best of all, you can build one yourself, and this is an amazing way of helping keep your home off the grid and self-sufficient.

    Watch the DIY efficient rocket mass heater build series

  • How to build an awesome Drill Powered Winch .Lift a Car or other Heavy loads effortlessly using a simple Cordless Drill
    This video shows how a simple Cordless Drill can effortlessly lift or move heavy loads. Definitely beats a Come Along.The winch in the video was purchased from Harbor Freight.With a snatch block this will lift 4000lbs which will pull a 20,000lb vehicle up a 10% grade.A snatch block is a really neat thing. By taking the cable out of the winch and through the pulley of the snatch block, then back to the winch it doubles the pull capacity. It also halves the speed of the item being pulled/lifted but it is a worthwhile trade off. You can keep adding pulleys and running back and forth to reduce the strain on the winch.You will see that a cordless drill lifting a car off the ground is pretty damn impressive

    Watch the DIY Homemade Cordless Drill Powered Winch Build Video

  • DIY Videos :How to generate Free Power for the rest of your life by building a Micro Hydro Electric Power system and kiss the Grid system goodbye.
    This 16 part Awesome Video series shows the overview and setup in detail of a Micro Hydro Electric Power System build for the long term from the ground up.What a hydroelectric system does is that it converts the force from flowing water into electricity. You take the kinetic energy of water flowing downhill from a stream or river and direct it onto a wheel in a turbine that converts the rotational energy to electricity. I have 2 natural springs that provide water which falls about 500 vertical feet through a mile of pipe and develops about 220 psi..Harness the power of hydropower; flowing water for clean, sustainable home free electricity 24/7 and ditch your dependency on the grid system for good. [the_ad id="6435"] The basic components of this build are A Stream Of Flowing Water - A hydroelectric generator is only useful in a bed of flowing water,Magnets - The magnets will spin against the coils to create an electric current.Bearing - Used for the disc to spin against,Coils - The coils will spin against the bank is to create an electric current.Half-Inch PVC Pipe - The disc will be placed on the PVC pipe.5-gallon bucket,Waterline - We are using the 5-gallon bucket and waterline to create a closed system. The overview of the steps mentioned in this video series: The first step in creating your hydroelectric generator is to create the discs. There are two parts to the disc, the stator and rotator disc. The stator disk is stationary and contains the coils. The rotator disc will be spun using the water current. The magnets will spin against the coils, creating an electric current. Now that we know the process, it is time to learn how you can make a hydroelectric generator yourself. You can create these discs using templates that you can find online. Trace the amount uncovered and use them as templates to cut the discs that you will be using. Make a hole in the discs ½ inch wide, so the half-inch PVC pipe can fit through the center of them. Place the discs side-by-side and attach the fins to the turbine. Attach the turbine to the rotator disc so it spins as the turbine spins. Make sure the fins are facing into the flow of water so that they will be pushed as the water passes through them. Next, attach the coils to the stator and at the magnets to the rotator disc. When you add the magnets, alternate them with their North and South poles. Make sure each north facing magnet is next to two south facing magnets. Likewise, make sure each south facing magnet is next to two north facing magnets. Add the turbine, rotator disc, and stator disk to the PVC pipe and rest it on top of the bucket. Pour water over The fins and the turbine will begin spinning. As the turbine spins, it will begin producing current as the bank is passed across the coils.
    Watch the step by step Micro Hydro Electric Power station Build Series